How much does it cost to hot tank an engine block?

The hot tank, pressure testing, and the Magnaflux test cost about $105 to $130. If the mains need to be align-honed (bored), add $180. Decking the block runs about $180. On the high end we have spent about $640; on the low end, $575.

Block Work

Bore V-8 Block (up to .060) $120.00
Competition Hone (with plate) $350.00
Finishing of Custom Unfinished Race Block Per Quote
Align Hone $125.00
Block True/Square Deck (up to .020) $185.00

Furthermore, how much does it cost to hone a block? I usually pay about $200 for boring, honing, hot tanking, decking w/ a plate, freeze plugs, and cam bearings. So your price sounds pretty in line.

Also Know, what does Hot tanking a block do?

Hot tanking is the traditional way to clean dirty cast iron engine blocks, heads etc. The hot tank is just a big metal tank with a very nasty, caustic hot water solution in it. The parts are submerged in the solution and allowed to soak for many hours with the solution slowly circulating around them.

Will hot tank remove rust?

A hot tank really will not do anything to rust. If you can find a machine shop that uses an oven and steel shot blaster to clean cast iron, that makes it look like new. The “acid” that they use to clean radiators will also get rid of rust.

How much should a valve job cost?

Know what price you should pay to get your vehicle fixed. The average cost for a valve adjustment is between $246 and $336. Labor costs are estimated between $220 and $278 while parts are priced between $26 and $58. Estimate does not include taxes and fees.

How much does it cost to machine a 350 block?

Overall, it looks like a typical replacement short block will be within $200 of very BASIC machine work. You can get a new GM 350 (L31) one piece short block from sdparts.com for $1200. Ebay has several in the $1600-$1800 range with new crank/rods/pistons.

How much does it cost to bore a cylinder?

Cylinder Boring Pricing Sheet CYLINDER BORING & HONING (MOST 2 & 4 CYCLE, PER HOLE) Boring, Honing and fitting of Piston & Rings $75.00 Race Type or Big Bore $250.00 ** Extra Charge for removal & fit of Power Valves (no final assembly) $21.00 OUTBOARDS & BLIND HOLES (Bore or Hone) – per hole

What is Magnafluxing engine block?

Simply stated, that is magnetic inspection. “Magnafluxing” an engine block or head or pistons merely means that the parts are exposed to a magnetic field. They are then dusted or sprayed with either a dry or wet solution of ferrous metal dust.

What is a decked block?

Decking the Block Decking is the process of cutting down the portion of the block to which the cylinder heads mate. Finally, a block must often be decked to achieve the proper deck height. Deck height is the distance from the crank centerline to the deck surface.

Can I use vinegar to flush my radiator?

Vinegar works well in removing these culprits because it is a mild acid that is safe to use on all metals. If you don’t want to pay someone to do a radiator flush, try using vinegar to get your car’s radiator back in good running condition.

How do you clean an engine block?

How to Clean Inside an Engine Block Mount the engine to an engine stand and connect the power washer or garden hose to a hot water source. Spray the engine block down with engine degreaser allowing it to soak in for the amount of time designated on the product label. Loosen built-up dirt and grime on the engine block with a stiff-bristled brush.

How much does cylinder head work cost?

The average repair cost You can be sure that it will cost at least $500, which includes labor and parts costs. If you were to replace the entire cylinder head, it would only cost $200 to $300 on average. With labor at about $90 to $100 per hour, this comes out to roughly $500 for the job.

How much do engine rebuilds cost?

A typical engine rebuild is between $2,500 and $4,000 in parts and labor costs. This type of engine repair might include simply replacing bearings and seals, and obviously taking the engine out and re-installing it.